Make sure that your browser is Java enabled...

 

 
  • Automatic Dry Priming and
    Repriming
  • Dry Running Capabilities
  • Enviornmentally Safe Priming
    System With No Blowby
  • Unattended Operation
  • Solids Handling Up To 3.38"
  • High Capacity Vacuum
    Compressor Provides
    Quick Priming
  • Flowrates: 500 - 3500 gpm
  • General Construction
  • Sewer Bypass
  • Lift Stations
  • Stormwater Control
  • Industrial Wastestreams
  • Dewatering Excavation
  • Tank Cleaning
  • Flood Drainage
  • Fire System Charging
 

Product Data Sheet
10JSC Pump
This pump uses an oil-lubricated two-cylinder piston compressor that is driven by v-belt off the shaft. A vacuum is created by forcing air through an air/water separator. A float-operated valve installed in the separator prevents liquid but allows air to exit the separation chamber. This pump develops higher discharge pressures than trash pumps due to the wear ring and closed impeller design.
Minimum Speed: 1400 rpm
Maximum Speed: 1800 rpm
Minimum Shutoff Head: 88 feet (38 psi) (1)
Maximum Shutoff Head: 139 feet (60 psi) (1)
Maximum Suction Lift: 28 feet (2)
Minimum Flow: 500 gpm
Maximum Flow: 3500 gpm
Maximum Suction Press: 100 psi
Maximum Casing Press: 160 psi
Maximum Temperature: 175°F
Maximum Solids Size: 3.38" spherical diameter
Impeller: 12.00" diameter, two vane,
enclosed with rear
equalizing vanes
Wearplate Clearance: 0.010" - 0.020"
Bearing Lubrication: Turbine oil ISO VG32 grade
(5W20 or 10W30 motor oil
can be used)
Vacuum System: Quincy 240P, V-belt driven
air cooled, two-cylinder compressor
modular design bronze venturi
Mech. Seal Lubrication: Oil lubricated
To the best of our knowledge, the technical data contained herein is true and accurate at the date of issuance and is subject to change without prior notice. NO WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY BAKER PUMPS, EITHER EXPRESSED OR IMPLIED.
Click on image to enlarge:
Suction Size: Ten inch
Discharge Size: Ten inch
Total Weight: 5400 lbs.
Overall Height: 7'-6"
Overall Width: 6'-0"
Overall Length: 14'-3"
Pump Casing/Head: Class 30 fine grain cast iron
Shaft Sleeve: 416 stainless steel
Ware Ring: Class 30 cast iron
Mechanical Seal Faces: Tungsten carb. / Tungsten carb.
Pump Shaft: Steel
Elastomers: Nitrile (Buna-N)
Impeller: Class 30 cast iron
Engine Make/Model: John Deere 6068D-125
Max. Continuous BHP: 94hp @ 1800 rpm
Crankcase Oil: SAE 10W40 (3)
Crankcase Oil Capacity: 18 quarts
Oil Press @ 850 rpm: 15 psi minimum
Safety Shutdowns: Low oil press./High water temp.
Grease Lubrication: No. 2 (3)
Fuel Capacity: 73 gallons
Fuel Consumption: ~3.5 gal/hr @ 1800 rpm
Fuel Type: Grade No. 2 diesel
Combustion System: Natural aspiration, direct inject
Noise Level: 98 dbA @ 1 meter
Run Time: 20 hours (4) @ 1800 rpm
Coolant Type: 50/50 water/antifreeze mix
Slow Idle Speed: 850 rpm
Number of Cylinders: Six
Bore x Stroke: 4.19"x5.00" (414 cu. in. total)
Fuel Filter: F91-RE50455-001
Oil Filter: F91-RE59754
Engine Air Filter: F91-C105004-000
Note:
(1) Based on 1.0 specific gravity.
(2) Depends on flowrate and pump speed.
(3) Midrange compromise. See John Deere manual.
(4) Per full fuel tank of 73 gallons.
Rev. 06/2000
In order to view the Pump Specifications, Adobe Acrobat is required
Download Pump Specifications
In Adobe Acrobat Format
© Copyright 2002 Baker Pumps. All rights reserved.
www.bakertanks.com www.andresswalsh.com www.bakerpumps.com