|
|
|
|
| This
pump uses an oil-lubricated two-cylinder piston compressor that
is driven by v-belt off the shaft. A vacuum is created by forcing
air through an air/water separator. A float-operated valve installed
in the separator prevents liquid but allows air to exit the
separation chamber. This pump develops higher discharge pressures
than trash pumps due to the wear ring and closed impeller design. |
|
|
|
|
|
|
 |
|
|
| Minimum Speed: |
1600 rpm |
| Maximum Speed: |
2400 rpm |
| Minimum Shutoff Head: |
225 feet (97 psi) (1) |
| Maximum Shutoff Head: |
490 feet (212 psi) (1) |
| Maximum Suction Lift: |
28 feet (2) |
| Minimum Flow: |
100 gpm |
| Maximum Flow: |
800 gpm |
| Maximum Suction Press: |
100 psig |
| Maximum Casing Press: |
175 psig |
| Maximum Temperature: |
150°F |
| Maximum Solids Size: |
0.50" |
|
|
|
|
|
|
|
 |
|
|
| Impeller: |
15.22" diameter |
| Wear
Ring Clearance: |
0.037" - 0.042" |
| Bearing Lubrication: |
Grease |
| Vacuum
System: |
Quinicy 216P, V-belt
driven
air-cooled, two-cylinder, 3.5
HP @ 60 psi, 3.00" bore x
2.50" stroke, |
| No. Impeller Vanes: |
Three, totally enclosed |
| Mech. Seal Lubrication: |
Oil lubricated |
|
Deadhead Pressure:
|
97 psi @ 1600 rpm |
|
|
|
|
|
| To the best of our knowledge,
the technical data contained herein is true and accurate at
the date of issuance and is subject to change without prior
notice. No guarantee of accuracy is given or implied because
variations can and do exist. NO WARRANTY OR GUARANTEE OF ANY
KIND IS MADE BY BAKER PUMPS, EITHER EXPRESSED OR IMPLIED. |
|
|
|
|
|
 |
|
Click on image to enlarge
|
|
|
|
|
|
 |
|
|
| Suction Fitting: |
Four-inch 125# flange |
| Discharge Fitting: |
Three-inch 125# flange |
| Total Weight: |
3300 lbs. |
| Overall Height: |
6'-10" |
| Overall Width: |
6'-2" |
| Overall Length: |
12'-6" |
|
|
|
 |
| Pump/Volute: |
Class 30 fine grain cast iron |
| Shaft Sleeve: |
416 stainless steel |
| Wear Ring: |
Bronze |
| Mechanical Seal Faces: |
Carbon against ceramic |
| Pump Shaft: |
Steel |
| Elastomers: |
Nitrile (Buna-N) |
| Impeller: |
SAE 40 brass |
|
|
|
 |
| Engine Make |
John Deere |
| Engine Model |
4045D |
| Max. Continuous BHP: |
76 @ 2500 rpm |
| Crankcase Oil: |
SAE 10W40 (3) |
| Oil Press @ 800 rpm: |
15 psi minimum |
| Safety Shutdowns: |
Low oil press./High water temp. |
| Grease Lubrication: |
No. 2 (3) |
| Fuel Capacity: |
60 gallons |
| Fuel Consumption: |
2.5 gal/hr @ 2000 rpm |
| Fuel Type: |
Grade No. 2 diesel |
| Combustion System: |
Direct injection |
| Noise Level @ BEP: |
90-95 dbA |
| Run Time: |
24 hours (@2000 rpm) |
| Collant Type: |
50/50 water/antifreeze mix |
| Slow idle Speed: |
800-850 rpm |
| Number of Cylinders: |
Four |
| Bore x Stroke: |
4.19"x5.00" |
| Fuel Filter: |
F91-RE50455-001 |
| Oil Filter: |
F91-RE597514 |
| Engine
Air Filter: |
F91-C085004 |
|
|
|
|
| Note: |
|
| (1) Based on 1.0 specific gravity. |
|
| (2) Depends on flowrate and pump
speed. |
|
| (3) Midrange compromise. See John
Deere manual. |
|
| (4) Includes weight of trailer,
pump and engine. |
|
| Rev. 02/2001 |
|
|
|
|
|
|
|
|
|
|
