Make sure that your browser is Java enabled...

 
  • Automatic Dry Priming and
    Repriming
  • Dry Running Capabilities
  • Environmentally Safe Priming
    System With No Blowby
  • Unattended Operation
  • Solids Handling Up To 3"
  • High Capacity Vacuum
    Compressor Allows
    Quick Priming
  • Flowrates: 100 -1790 gpm
  • General Construction
  • Sewer Bypass/Lift Stations
  • Stormwater Control
  • Industrial Wastestreams
  • Industrial Wastestreams
  • Wellpointing/Dewatering
  • Tank Cleaning
  • Quarries/Mine Water
  • Fire System Charging
 

Product Data Sheet
6TSV Dry Prime Pump
This pump uses an oil-flooded rotary vane vacuum pump that is driven by v-belt off the shaft. This creates a vacuum that draws air through an air/water separator. A float-operated valve installed in the separator prevents liquid but allows air to enter the vacuum pump. A constant stream of oil is fed from a reservoir through a shell and tube heat exchanger to the vacuum pump and exhausted into an air/oil separator. A valve in the separation chamber allows for flooded suction applications.
Minimum Speed: 1200 rpm
Maximum Speed: 2000 rpm
Minimum Shutoff Head: 54 feet (23 psi) (1) (@ 1200 rpm
Maximum Shutoff Head: 148 feet (64 psi) (1) (@ 2000 rpm
Maximum Suction Lift: 28 feet (6)
Minimum Flow: 100-200 gpm
Maximum Flow: 1790 gpm
Maximum Suction Press: 100 psi
Maximum Casing Press: 125 psi
Maximum Temperature: 190°F
Maximum Solids Size: 3" spherical diameter
Impeller: 11.25" diameter, two-vanes
Wearplate Clearance: 0.010" - 0.020" (rear)
0.010" - 0.020" (front)
Bearing Lubrication: No. 2 grease
Vacuum System: Rotary vane vacuum pump,
118 CFM, SAE30 oil lubricated
Mech. Seal Lubrication: SAE 30 oil lubricated
Deadhead Pressure:

@ 1600 rpm

 36 psi - 42 psi

@ 1800 rpm

 45 psi - 53 psi

@ 2000 rpm

 54 psi - 64 psi
To the best of our knowledge, the technical data contained herein is true and accurate at the date of issuance and is subject to change without prior notice. NO WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY BAKER PUMPS, EITHER EXPRESSED OR IMPLIED.
Click on image to enlarge:
Suction Fitting: Six-inch 125# Male Bauer
Discharge Fitting: Six-inch 125# Male Bauer
Total Weight: 6000 lbs. (approx) (2)
Overall Height: 7'-8"
Overall Width: 5'-8"
Overall Length: 11'-6"
Casing/Volute: Cast iron
Shaft Sleeve: 304 stainless steel
Wareplate: Carbon steel
Mechanical Seal Faces: Tungsten carb. / Tungsten carb.
Pump Shaft: 15-5 PH stainless
Elastomers: Nitrile (Buna-N)
Impeller: Ductile iron
NRV Body: Cast iron
NRV Flapper: Nitrile (Buna-N)
Air Sep. Ball/Seat: Rubber/Bronze
Engine Make/Model: John Deere 4045D
Crankcase Oil: 14 quarts of SAE 10W40 (3)
Oil Press @ 800 rpm: 15 psi minimum
Safety Shutdowns: Low oil press./High water temp.
Grease Lubrication: No. 2 (3)
Fuel Capacity: 60 gallons of No. 2 diesel
Fuel Consumption: 2.5 gal/hr @ 2000 rpm
Noise Level @ BEP: 90-95 dbA
Run Time: 24 hours + (4)
Coolant Type: 50/50 water/antifreeze mix
Idle / Rate Speed: 850 rpm/3000 rpm (5)
Number of Cylinders: Four
Bore x Stroke: 4.19"x5.00" (279 cu. in. total)
Fuel Filter: John Deere RE60021
Oil Filter: John Deere RE59754
Engine Air Filter: John Deere C085004
Note:
(1) Based on 1.0 specific gravity.
(2) Includes weight of trailer, pump and engine
(3) Midrange compromise. See John Deere manual.
(4) At 2000 rpm. Run time increases with reduced speed and decresase with higher speed.
(5) WARNING: This is the rated speed for the ENGINE ONLY. The rated speed of the pump is only 2000 rpm
(6) Depends on flowrate and pump speed.
Rev: 10/2000
In order to view the Pump Specifications, Adobe Acrobat is required
Download Pump Specifications
In Adobe Acrobat Format
© Copyright 2002 Baker Pumps. All rights reserved.
www.bakertanks.com www.andresswalsh.com www.bakerpumps.com